Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI)

Here you have the best Cisco 300-430 practice exam questions

  • You have 326 total questions across 66 pages (5 per page)
  • These questions were last updated on February 17, 2026
  • This site is not affiliated with or endorsed by Cisco.
Question 1 of 326
On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection to the WLC, all clients are disconnected, and the SSID is no longer advertised. Considering that FlexConnect local switching is enabled, which setting is causing this behavior?
Answer

Suggested Answer

The suggested answer is A.

The behavior described in the question suggests that the SSID is no longer advertised and all clients are disconnected due to the AP losing connection to the WLC while in standalone mode. This is likely because ISE NAC (Network Admission Control) is enabled. When NAC is enabled, it requires real-time communication with the WLC to validate client access. If the connection to the WLC is lost, the AP cannot perform the necessary NAC validations, leading to the disconnection of clients and the cessation of SSID broadcasts.

Community Votes17 votes
ASuggested
65%
D
29%
C
6%
Question 2 of 326
An engineer must implement intrusion protection on the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which AP mode and submode must be implemented?
Answer

Suggested Answer

The suggested answer is D.

An engineer must implement intrusion protection on the WLAN without compromising the existing coverage, especially in a historic building where adding new APs is difficult. Local mode allows the AP to serve clients while remaining largely on-channel, ensuring that the existing coverage is maintained. The WIPS (Wireless Intrusion Prevention System) submode adds the necessary protection against on-channel attacks. Therefore, the best implementation is AP mode: local with the submode: WIPS.

Community Votes7 votes
DSuggested
57%
B
29%
A
14%
Question 3 of 326
An engineer is implementing a FlexConnect group for access points at a remote location using local switching but central DHCP. Which client feature becomes available only if this configuration is changed?
Answer

Suggested Answer

The suggested answer is D.

The correct answer is mDNS. When using FlexConnect with local switching, mDNS (Multicast DNS) is not supported. For mDNS to be available, the configuration needs to be changed to central switching. Local switching limits the capabilities of mDNS snooping, which is necessary for the feature to function correctly.

Community Votes5 votes
BMost voted
100%
Question 4 of 326
A FlexConnect remote office deployment is using five 2702i APs indoors and two 1532i APs outdoors. When a code upgrade is performed and FlexConnect Smart
AP Image Upgrade is leveraged, but no FlexConnect Master AP has been configured, how many image transfers between the WLC and APs will occur?
Answer

Suggested Answer

The suggested answer is B.

In a FlexConnect Smart AP Image Upgrade scenario, if no FlexConnect Master AP is configured, the AP with the lowest MAC address within each model type (e.g., one for the 2702i APs and one for the 1532i APs) will be chosen automatically to download the image from the WLC. Subsequently, these chosen APs will distribute the image to the rest of the APs of the same model. Thus, two image transfers between the WLC and APs will occur: one for the 2702i model and one for the 1532i model.

Community Votes2 votes
BSuggested
50%
D
50%
Question 5 of 326
Where is a Cisco OEAP enabled on a Cisco Catalyst 9800 Series Wireless Controller?
Answer

Suggested Answer

The suggested answer is B.

A Cisco OEAP (OfficeExtend Access Point) is enabled on a Cisco Catalyst 9800 Series Wireless Controller within the Flex Profile. The Flex Profile is specifically designed for offering extended and flexible configuration options, including the OfficeExtend feature which allows home office environments to be securely connected to the corporate network.

Community Votes3 votes
BSuggested
100%

About the Cisco 300-430 Certification Exam

About the Exam

The Cisco 300-430 (Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI)) validates your knowledge and skills. Passing demonstrates proficiency and can boost your career prospects in the field.

How to Prepare

Work through all 326 practice questions across 66 pages. Focus on understanding the reasoning behind each answer rather than memorizing responses to be ready for any variation on the real exam.

Why Practice Exams?

Practice exams help you familiarize yourself with the question format, manage your time, and reduce anxiety on the test day. Our 300-430 questions are regularly updated to reflect the latest exam objectives.