Professional VMware NSX-T Data Center

Here you have the best VMware 2V0-41.20 practice exam questions

  • You have 92 total questions across 19 pages (5 per page)
  • These questions were last updated on February 22, 2026
  • This site is not affiliated with or endorsed by VMware.
Question 1 of 92
An NSX administrator noticed that the nsxcli command times out after 600 secs of idle time.
Which CLI command disables the nsxcli time out value on NSX Manager?
Answer

Suggested Answer

The suggested answer is A.

To disable the nsxcli timeout on NSX Manager, the correct command is 'set cli-timeout 0'. This sets the inactivity timeout to 0 seconds, effectively disabling it.

Community Votes6 votes
ASuggested
100%
Question 2 of 92
An NSX administrator is configuring the KVM hypervisor host as a transport node and wants to apply the Failover Order as a NIC teaming policy.
Which profile allows the administrator to configure the NIC Teaming policy as Failover Order?
Answer

Suggested Answer

The suggested answer is D.

To configure the NIC Teaming policy as Failover Order on a KVM hypervisor host, the administrator should use the Uplink Profile. The Uplink Profile allows the configuration of various settings, including the NIC Teaming policies, which can be set to Failover Order to determine the order in which NICs are used for network traffic.

Community Votes2 votes
DSuggested
100%
Question 3 of 92
Which two choices are prerequisites to configure NSX-T on VDS? (Choose two.)
Answer

Suggested Answer

The suggested answer is D, E.

To configure NSX-T on vSphere Distributed Switch (VDS), two primary prerequisites are required: a vSphere Distributed Switch version of at least 7.0, and a Maximum Transmission Unit (MTU) setting of 1600. VDS 7.0 provides the necessary features and capabilities to support NSX-T, while an MTU of 1600 ensures that the network can handle the overhead required by NSX-T encapsulation protocols such as Geneve. An MTU of 1500 or 1400 would be insufficient for this purpose.

Community Votes1 vote
DESuggested
100%
Question 4 of 92
Which command is used to display the network configuration of the Tunnel Endpoint (TEP) IP on a bare metal transport node?
Answer

Suggested Answer

The suggested answer is A.

The command 'ifconfig' is used on Unix-based systems, including Linux, to display the configuration of network interfaces. Since a bare metal transport node typically uses a Linux-based operating system, 'ifconfig' would be the appropriate command to display the network configuration of the Tunnel Endpoint (TEP) IP.

Community Votes

No votes yet

Join the discussion to cast yours

Question 5 of 92
Which three steps are required to create an IPsec VPN tunnel? (Choose three.)
Answer

Suggested Answer

The suggested answer is A, B, C.

To create an IPsec VPN tunnel, three essential steps are required: First, create an IPsec service to initiate the VPN setup process. Second, add a local endpoint, which serves as the local termination point for the VPN tunnel. Finally, configure an IPsec session to establish secure communication details and parameters for the tunnel.

Community Votes

No votes yet

Join the discussion to cast yours

About the VMware 2V0-41.20 Certification Exam

About the Exam

The VMware 2V0-41.20 (Professional VMware NSX-T Data Center) validates your knowledge and skills. Passing demonstrates proficiency and can boost your career prospects in the field.

How to Prepare

Work through all 92 practice questions across 19 pages. Focus on understanding the reasoning behind each answer rather than memorizing responses to be ready for any variation on the real exam.

Why Practice Exams?

Practice exams help you familiarize yourself with the question format, manage your time, and reduce anxiety on the test day. Our 2V0-41.20 questions are regularly updated to reflect the latest exam objectives.