Exam 200-301 All QuestionsBrowse all questions from this exam
Go to Exam
Question 1260

SIMULATION

-

Guidelines

-

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.

• Refer to the Topology tab to access the device console(s) and perform the tasks.

• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.

• All necessary preconfigurations have been applied.

• Do not change the enable password or hostname for any device.

• Save your configurations to NVRAM before moving to the next item.

• Click Next at the bottom of the screen to submit this lab and move to the next question.

• When Next is clicked, the lab doses and cannot be reopened.

Topology

-

Tasks

-

R1 has been pre-configured with all the necessary commands. All physical cabling is in place and verified. Connectivity for PC1 and PC2 must be established to the switches, and each port must only allow one VLAN.

1. Configure SW-1 with VLAN 35 and label it exactly as SALES

2. Configure SW-2 with VLAN 39 and label it exactly as MARKETING

3. Configure the switch port connecting to PC1

4. Configure the switch port connecting to PC2

5. Configure SW-1 and SW-2 for universal neighbor discovery using the industry standard protocol and disable it on the interface connecting to PC1

    Correct Answer:

Discussion
picho707

Task 1 SW-1(config)#vlan 35 SW-1(config-vlan)#name SALES Task 2 SW-2(config)#vlan 39 SW-2(config-vlan)#name MARKETING Task 3 SW-1(config)#interface gigabitEthernet 0/2 SW-1(config-if)#switchport mode access SW-1(config-if)#switchport access vlan 35 Task 4 SW-2(config)#interface gigabitEthernet 0/2 SW-2(config-if)#switchport mode access SW-2(config-if)#switchport access vlan 39 Task 5 SW-1(config)#interface gigabitEthernet 0/2 SW-1(config-if)#no lldp receive SW-1(config-if)#no lldp transmit SW-2(config)#lldp run

JulesAZ

Really appreciate all your answers on these sim q's picho :) Far be it from me, honestly, to try to correct, however do you need to enable lldp on SW1 for task 5 and then as you have shown disable it on the specified interface e0/2?

picho707

Correct, I think I posted them out of sequence.

picho707

Correction to Task 5 SW-2(config)#lldp run SW-1(config)#lldp run SW-1(config)#interface gigabitEthernet 0/2 SW-1(config-if)#no lldp receive SW-1(config-if)#no lldp transmit SW-1#show lldp interface gigabitEthernet 0/2 GigabitEthernet0/2: Tx: disabled Rx: disabled Tx state: INIT Rx state: INIT

AbdullahMohammad251

We need to disable neighbor discovery using cdp : SW(config)# no cdp run Also, we need to enable lldp on the rest of the interfaces: SW2(config) interface range e 0/0-2 SW2(config-if) lldp transmit SW2(config-if)# lldp receive SW1(config) interface range e 0/0-1 SW2(config-if) lldp transmit SW(config-if) lldp receive

AbdullahMohammad251

The suggested answer is correct but is missing the commands I have mentioned above.

86a50a6

this is not true brother, once you enable lldp globally all interfaces will transmit and receive lldp packets. It is only necessary to disable it if you don't want packets to be TR/RC from a specific interface. I tested and approve my answer regarding this matter, wa salamou alaikoum wa rahmatou allah.

bymrdas

Task 1 SW-1(config)#vlan 35 SW-1(config-vlan)#name SALES Task 2 SW-2(config)#vlan 39 SW-2(config-vlan)#name MARKETING Task 3 SW-1(config)#interface gigabitEthernet 0/2 SW-1(config-if)#switchport mode access SW-1(config-if)#switchport access vlan 35 Task 4 SW-2(config)#interface gigabitEthernet 0/2 SW-2(config-if)#switchport mode access SW-2(config-if)#switchport access vlan 39 Task 5 SW-1(config)#interface gigabitEthernet 0/2 SW-1(config-if)#no lldp receive SW-1(config-if)#no lldp transmit SW-1(config)#lldp run SW-2(config)#lldp run

bymrdas

The given answer is correct