The Cisco Nexus switch Generic Online Diagnostics policy for a PortLoopback test requires 10 consecutive failures to error disable the port. The customer wants to change it to 5 consecutive failures. Which configuration applies the changes for module 1 only?
The correct configuration to apply the changes for module 1 specifically should include the command 'mod 1' to target the desired module and use 'testing-type monitoring' as that is the appropriate testing type for this context. Additionally, the command 'publish-default' is necessary to apply the new policy correctly, despite some debate about the existence of this command. Therefore, the configuration that meets these criteria is the one provided in option B.
B is correct: Option A is incorrect because it uses the testing-type bootup command instead of testing-type monitoring, and it publishes an event instead of setting the new policy as default. Option C is incorrect because it applies the changes to all modules instead of module 1 only, and it uses the policy-default command instead of publish-default. Option D is incorrect because it uses the testing-type bootup command instead of testing-type monitoring, and it uses the policy-event command instead of publish-default.
It's C, policy-event doesnt exist, its policy-default https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5600/sw/system_management/7x/b_5600_System_Mgmt_Config_7x/configuring_eem.pdf
but C applies it to all modules, not 1. Thus there is no real correcdt answer....
https://docplayer.net/45256558-Advanced-troubleshooting-nexus-7000-series-switches.html GOLD: Generic On-Line Diagnostics GOLD tests & corrective actions are run via EEM as system policies Nexus(config)# show event manager system-policy Name : PortLoopback Description : Do CallHome, log error and disable further HM testing on affected ports after 10 consecutive failures of GOLD "PortLoopback" test Overridable : Yes Can override various GOLD test s parameters Original portloopback policy required 10 consecutive failures Nexus(config)# event manager applet custom-portloopback override PortLoopback Nexus(config-applet)# event gold mod 2 test PortLoopback testing-type monitoring consecutive-failure 5 Nexus(config-applet)# action 1 policy-default Nexus(config-applet)# show event manager policy internal Name : custom-portloopback (overrides PortLoopback) Policy Type : applet Event Specification : event gold module 2 test PortLoopback testing-type monitoring After overriding policy, consecutive-failure 5 now requires only 5. Action : 1,sup:service:default Event Specification active on : Active
This configuration sets up a custom applet named "custom-PortLoopback" that overrides the default PortLoopback test for module 1. It specifies the testing type as "bootup" and sets the consecutive failure threshold to 5. The "action 1 policy-event" line is included to publish the event.
C should be the answer https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/8_x/config/system-management/cisco_mds9000_system_management_config_guide_8x/configuring_the_embedded_event_manager.html#con_1000285 Note If you want to allow the triggered event to process the default actions also, you must explicitly configure an EEM action with event-default or policy-default, based on the type of policy. For example, if you match a CLI command in a match statement, you must add the event-default action statement to the EEM policy. If the event-default action statement is not added, EEM will not allow the CLI command to execute.
I guess c is correct
Policy-default action is needed (see link below) and it is stated that it needs to be done to module 1 only, thus D is the good answer. https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus6000/sw/system_management/7x/b_6k_System_Mgmt_Config_7x/configuring_eem.html#reference_AFFC2A67E67D451C9EFE27C1C7BE4E70
D can't be correct due to testing-type bootup. Testing-type should be monitoring. Hence C is closest if it had "mode 1" instead of "mode all"
C) monitoring and policy-default publish-XXX is not an option. bootup is not an option. There are one thing that i think is wrong in C) but there are no correct choice. The question says "for module 1 only" . And C) indicates "mod all". I think in real exam sure should say "mod 1"
tried on my nexus C is the only one that make sense with policy-default
policy-default is the only valid fof all those command
Then why not B? The C option is applying for all of the modules and not only module 1 as it requested.
Looks like C is correct as we need to have monitoring https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/eem/command/eem-cr-book/eem-cr-e1.html#:~:text=scheduled%20diagnostic%20tests.-,monitoring,-%2D%2DSpecifies%20the%20diagnostic and the only correct other option is policy-default https://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/8_x/config/system-management/cisco_mds9000_system_management_config_guide_8x/configuring_the_embedded_event_manager.html#con_1000285:~:text=action%20number-,policy%2Ddefault,-Executes%20the%20default publish-default doesn't exist.. we have publish-event only
The answer should be << C >> There is no command as publish-default
B is correct
d is correct!
page - 30 https://www.ciscolive.com/c/dam/r/ciscolive/us/docs/2017/pdf/BRKDCN-3234.pdf