NetApp Certified Storage Installation Engineer, ONTAP

Here you have the best Netapp NS0-182 practice exam questions

You have 66 total questions to study from
Each page has 5 questions, making a total of 14 pages
You can navigate through the pages using the buttons at the bottom
This questions were last updated on November 20, 2024

Question 1 of 66

You are completing an ONTAP base installation, and your customer is asking you to create two SVMs, one for NFS and one for SMB.

Which type of SVM needs to be created to complete the installation?

system SVM

data SVM

admin SVM

multitenancy node SVM

Correct Answer: B

To complete the installation of ONTAP and create two SVMs, one for NFS and one for SMB, a data SVM needs to be created. Data SVMs are used for serving data and providing access to storage resources, making them suitable for both NFS and SMB protocols.

Question 2 of 66

Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

Active IQ

Config Advisor

NetAppDocs

Fusion

Correct Answer: C

NetAppDocs is a tool that utilizes PowerShell to generate comprehensive site design documentation, making it suitable for producing detailed handover reports to the customer. It can create documents in various formats such as Excel, Word, and PDF, which helps in delivering well-structured and sanitized output for sensitive data environments.

Question 3 of 66

Which LIF type is used by default for hardware-assisted storage failover communication?

intercluster

node-mgmt

data

cluster-mgmt

Correct Answer: B

The type of LIF (Logical Interface) used by default for hardware-assisted storage failover communication is the node-mgmt LIF. This type of LIF is specifically designated for managing the nodes in a storage cluster and is, therefore, suitable for handling storage failover communications.

Question 4 of 66

You install a new FAS2650 HA with a DS224C disk shelf and ONTAP 9.5 on a customer site.

Referring to the exhibit, which steps are required to get an HA cabled system?

1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.

1. Insert a cable from right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. 2. Insert a cable from left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3.

1. Insert a cable from right controller port 0a to IOMB port 1, and from port 0b to IOMA port 4. 2. Insert a cable from left controller port 0a to IOMA port 1, and from port 0b to IOMB port 4. 3. Cable the out-of-band ACP.

1. Insert a cable from right controller port 0a to IOMB port 2, and from port 0b to IOMA port 3. 2. Insert a cable from left controller port 0a to IOMA port 2, and from port 0b to IOMB port 3.

Correct Answer: B

To set up an HA (High Availability) cabled system for a NetApp FAS2650 with a DS224C disk shelf running ONTAP 9.5, follow these steps: Connect a cable from the right controller port 0a to IOMA port 1, and from port 0b to IOMB port 3. Then, connect a cable from the left controller port 0a to IOMB port 1, and from port 0b to IOMA port 3. This configuration ensures proper communication and redundancy between the controllers and the respective ports.

Question 5 of 66

You just installed two nodes into an existing ONTAP cluster. When running date on the CLI you notice that the cluster1-03 node is running behind time. You confirmed that you can reach the node management LIF of each node.

Referring to the exhibit, which statement is true?

The node-management LIF has to be on e0M for NTP to work.

The DNS is not configured for this node.

The NTP is adjusting in small increments.

No NTP server is configured for this node.

Correct Answer: D

The exhibit shows that the NTP server (192.160.0.10) is configured but the 'Is Preferred Server' column is set to true only for one node, indicating it may not be set properly for others including cluster1-03. Additionally, there is no indication that DNS settings are involved in this issue. The problem is likely due to an NTP server misconfiguration, making the most accurate statement that no NTP server is configured properly for the node.